+1-226-980-7625 (ROCK)
Oldenburg Canon Bolter
2008 Atlas Copco CM785D
Tamrock DHA 400-1
2014 Epiroc SmartRoc D65 DTH
2016 Epiroc Smartroc D60-SF
Eng-10008 Imp-6553
- ROC Angie
- Diesel preheat
- COP 1840 Drifter
AVO09A1172
2014 Sandvik DX 800.2 Serial # 38170
Frame Hours: 7283 Hrs
Hammer : 1387 Hrs.
2015 Gill Beetle w. Truck and Compressor
2015 Case CX300C excavator with the REV Drill package
Pre-Owned Equipment
2023 Word Rock Drill "New"
2009 ROC D3RRC
Fully Serviced and 100% ready to drill SmartRoc D65 SF
10,400 Hours
This rig is fully capable to drilling and retracting its drill pipe on its own.
Frame/Engine 5,000 hours
COP 3060ME Drifter.
This machine is being sold as is where is no warranties expressed or implied so no guarantees
Started and drilled 3 months ago
Unit is priced to move.
Eng -14559 Re-man Caterpillar engine was put in at 11,080 hours. So approximately 3500 Hours on current engine Imp-7965 .
COP 2560 Drifter
REV Drill package. This package is mounted on a very clean 2015 Case CX300C excavator (1800 Hours) with the REV Drill package that has the capability of drilling 3.5”-9+ inch hole diameters. The mast is 30’+10” or 40 foot of travel. Approx. 50 foot total length.
2010 Atlas Copco ROC F9C
More Pre-Owned Equipment coming soon!!
For details and Pricing contact: operations@rockremovalsupplies.com
Set up today to run T38 rods but would
normally run R32.
This mid 80s Tamrock Zoom track DHA 400 runs very well and all functions do operate. The original owner John Joseph out of New Jersey who runs strictly Sandvik/Tamrock rigs took the drilling controls off the mast and set them on the left side of the rig next to the boom controls and tram station. He then reset the mast 90 degrees to the left so that the operator could easily see the hammer etc.
rig over approximately 10,000.
The engine is not the original 6 Cylinder Deutz as it has the local Deutz dealer tag on it as a reman. The rig did
start up right away after sitting for two months and every function worked well.
6525 Frame/Engine Hours
2636 Hammer/compressor.
Set up to run 4" x 2 7/8" API Thread pipe.
Runs very solid,
Currently being serviced at the local Epiroc service center.
FR T50-10 AVO11A1484
2012 Atlas Copco D3RRC- New engine installed 2400 hours ago, COP 1840HE drifter just rebuilt by Epiroc USA, 100% ready to go to work
Word Rock Drill with a 540 Doofer drifter 360 positioner and a clamp. It has 10ft of travel on the mast. Looking to sell or rent out.
18" DTH + 30" Button Bit
Canon Bolter- With a basket / Dust Collector
Model DP12-HD- RB/M
Details pending
2014 Sandvik Dx800 S/N 38170
2012 Atlas Copco D3RRC
Epiroc T20R Crawer Drill
Chris Cuter 5' Stone Cutter
HD50-RB Multi-Purpose Robot
Flexiroc T20R
Serial Number: AVO11V1008
Hours: 1548
Epiroc T20R Crawer Drill with rotary Boom head for upwaard vertical drilling if needed.